How to Install a Ghost Immobiliser
A ghost immobiliser is a hidden security device that protects your vehicle from key cloning and hacking. It prevents the vehicle's engine from starting until it is started with a PIN code that can be up to 20 characters long.
It is undetectable by thieves who don't be expecting this extra layer of security. Certain systems come with an app that allows the owner to disarm their immobiliser in the event of forgetting their PIN code or to use the service/valet mode.
Connecting the vehicle's CAN Bus
The Ghost 2 Immobiliser is a cutting-edge security system that can be integrated into your vehicle's ECU offering a secure protection against thieves. It is extremely efficient and user-friendly. This makes it a valuable addition to your vehicle's security arsenal. Like any anti-theft device, it's not foolproof and requires regular maintenance in order to function effectively. Luckily, this guide will aid you in getting the most out of your Ghost 2 Immobiliser.
CAN (Controller Area Network), a robust serial networking system that lets microcontrollers communicate with each other over short distances. Central control units is not required. ghost immobiliser near me is designed for multiplexing electrical wiring within vehicles to cut down on copper and offers a range of advantages, including low cost and a simple use.
The CAN protocol is used in most modern vehicles to communicate with the engine management system, steering control module air conditioning controls and more. It also transmits sensor data like inputs and speed sensors, to control the various functions of the vehicle. The CAN bus is used to monitor these diverse components, and it can stop a vehicle from starting if they're in a dangerous state.
It's crucial to understand how the CAN bus functions and how it's secured. It is possible to add additional features to vehicles using CAN bus, but it's crucial to safeguard it against hackers and other threats. Installing a firewall, and monitoring your CAN-bus using software is the best method to accomplish this.
Ghost2's control unit is hidden inside the car's dashboard or wiring harness, preventing thieves from physically tampering with it. It's also impossible to reset the PIN or emergency code without access to the vehicle.
You can enable Transport Mode If you need to sell your car for service, valet parking or for any other reason. This feature will disable both the keyfob and ignition functions of the Ghost immobiliser. It will only be activated when the vehicle has reached 31 mph for a time of 15 minutes.
How do you create a PIN code
The Ghost immobiliser is an effective security system that protects your vehicle from thieves. The innovative technology uses the PIN to disable the engine of your vehicle and prevent it from starting if you don't have the correct code, or an authorized fob/mobile. The system's discrete design makes it unnoticeable, and also provides unbeatable security against theft. Moreover the system is TASSA verified and can provide significant savings on insurance premiums for cars.
During the installation, Ghost enters a "learning mode" to record the sequence of buttons that are that are pressed to generate your unique pin codes. After the pin code is created and the installer has completed its work, it will guide you through the process of activating the system. Once activated the Ghost system disables the vehicle's start motor unless you enter a valid pin or switch the vehicle into transport mode. This makes it extremely difficult for thieves to duplicate or hack into your vehicle's start system.
Installing an Ghost immobiliser is easy, but it is important to follow the detailed instructions in the user manual to ensure that it operates properly. Hand tools are essential in making accurate connections and a multimeter will help you verify the electrical value. Insulation tape, heat shrink tubing, and cable ties can be used to protect exposed wiring. Test the system on a regular basis to identify any potential issues.
It is essential to test the system one more time before you turn on the ignition. Ghost immobilisers are able to rearm themselves after 3 to 30 seconds, dependent on the model of your vehicle. The system also comes with a Service/Valet mode that allows you to temporarily remove the system for servicing your vehicle or parking valet.
Ideally, the immobiliser should be concealed in a discreet location beneath the steering wheel or on the dashboard. It is recommended to use a small bit of paint or duct tape to mark the CAN H and L wires, so that you can easily locate them when you are testing. The CAN H and the L wires should also be connected to an electrical source that can provide an uninterrupted 12V. It is crucial to verify the connections again after testing as incorrect identification of these wires could cause the system to malfunction.
Activating the system
A ghost immobiliser prevents your vehicle from starting until you press a set of buttons within the car, usually the steering wheel, door panel, or central console. The sequence can be changed by the user at any time. Once activated, the system can't be deactivated. This makes it an ideal choice for anyone who wants to secure their vehicle against theft.
The device is not designed to be detectable by modern diagnostics and code-grabbing techniques. It doesn't emit radio frequency either, making it even more difficult for thieves identify.
If the device is located, it will stop the engine from starting. It will also sound an alarm to scare the burglar away. The device can be used to monitor the location of a car, which will aid in the search for the vehicle if it is stolen.
Contact Car Specalist Customs for a estimate or to discuss your options if you're interested in Ghost immobiliser. We are fully trained to install a ghost immobiliser on your vehicle and will make sure it is hidden in a hard-to-reach area. We can also install other security measures, such as the kill switch and wheel lock to ensure your vehicle is secure from thieves.
Disarming the System
If you own a Ghost immobiliser installed to your vehicle, it's important to know how to disarm it. It can be used in the event that you lose your keys or your battery fails. The system utilizes a unique PIN code that only you are aware of. It will not start the vehicle without this code. Pressing a combination buttons on the dashboard or steering wheel is the most efficient method to enter your code. This is a lot easier than using a key fob. It also keeps others from copying the remote.
Contrary to other aftermarket immobilisers which require cutting wires for installation, Ghost2 is non-invasive and works with your vehicle's CAN bus network to operate. Its standout feature is its ability to bypass the engine without impacting your vehicle's normal functions, making it difficult for thieves to make use of signal boosters or copy your car keys. Moreover, it does not emit radio frequencies, so thieves won't be able to detect it.
The Ghost system also has an option called Transport Mode, which allows you to temporarily disable the security system for circumstances like transportation or servicing. This feature is great if you are lending your vehicle to someone else without sharing your PIN code or if your vehicle needs to be kept secure when you drive it. To activate Transport Mode you need to press the service button 5 times within a period of 2 seconds. The Ghost system will confirm activation by five indication signals.
After you're done, make sure to save the emergency code in a safe place away from your vehicle. If you happen to encounter a situation where you are locked out of your vehicle, you can contact the technician or company who installed the system, and they'll give you the code. If they are not able to contact you then you can attempt to contact an authorized dealer however this will require verification procedures and could incur additional fees.
In addition to the convenience of this system, you can count on it to guard your vehicle from theft and reduce insurance costs. Many insurance companies offer lower rates or financial incentives to install this system to prevent theft.